专注通风管道加工·排烟罩

济南油烟净化器会随着使用时间的增长，内部堆积很多的油渍，如果不及时的进行清洗，那么很难达到好的净化效果，接下来给大家介绍一下油烟净化器清洗工作的规范内容。

Jinan lampblack purifier will accumulate a lot of oil stains with the increase of use time. If it is not cleaned in time, it will be difficult to achieve a good purification effect. Next, I will introduce the standard content of lampblack purifier cleaning.

1、关闭电源并给负载放电

1. Turn off the power supply and discharge the load

关闭机身上的电源开关，但由于电箱内有电，在维修设备前要关闭济南油烟净化器外的总电源开关。请勿带电作业，以确保清洁工的。

Turn off the power switch on the machine body, but because there is electricity in the electric box, turn off the main power switch outside the Jinan lampblack purifier before maintaining the equipment. Do not work with electricity to ensure the safety of cleaners.

打开设备检修门后，在去除电场之前，释放电场中的残留电荷。使用螺丝刀将放电场中的残余电荷放电。具体操作是用手握住螺丝刀的绝缘手柄，利用螺丝刀的金属部分在电场中缩短任何圆柱体的阴力。

After opening the equipment access door, release the residual charge in the electric field before removing the electric field. Use a screwdriver to discharge the residual charge in the discharge field. The specific operation is to hold the insulated handle of the screwdriver by hand, and use the metal part of the screwdriver to shorten the negative force of any cylinder in the electric field.

用户在清理电场时，要严格及时清理机箱内部的油渍，以火灾隐患。

When cleaning the electric field, users should strictly and timely clean the oil stains inside the chassis to eliminate the potential fire hazard.

2、拧下螺丝并去除电场

2. Unscrew the screws and remove the electric field

确认电源已关闭后，拆下固定螺栓，打开维修门，用手拉动两侧电场，待电场即将释放时，用手握住前端。避免突然跌落损坏电场。

After confirming that the power supply has been turned off, remove the fixing bolts, open the maintenance door, pull the electric field on both sides by hand, and hold the front end by hand when the electric field is about to release. Avoid sudden drop to damage the electric field.

3、取下附件以方便清洁

3. Remove accessories for cleaning

由于绝缘体上的潮湿土壤很可能是造成漏电的原因，因此在移除绝缘体的同时，将针与阴力分开，将针筒与阳力分开，更容易清洁。

As the damp soil on the insulator is likely to be the cause of electric leakage, it is easier to clean by separating the needle from the negative force and the needle cylinder from the positive force while removing the insulator.

4、清洗、浸泡、冲洗电场

4. Cleaning, soaking and washing electric field

使用不锈钢或塑料清洗罐式容器，形状大于电场。清洁时将油烟净化器包裹起来，以免弄脏地板，然后将包裹排放到容器中。用重量比为1:20的碱和热水混合溶液起泡清洗时，浸泡时间视油渍程度而定。浸泡后，用高压水枪冲洗干净，放在干净的地方晾干。

Use stainless steel or plastic to clean the tank container, which is larger than the electric field. When cleaning, wrap the oil fume purifier to avoid soiling the floor, and then discharge the package into the container. When the mixed solution of alkali and hot water with a weight ratio of 1:20 is used for foaming cleaning, the soaking time depends on the degree of oil stain. After soaking, wash it with a high-pressure water gun and place it in a clean place to dry.

5、绝缘子的检查和清洗

5. Inspection and cleaning of insulators

如果绝缘子在检查过程中燃烧，如果破裂则更换。您需要将绝缘子和绝缘子上的油清洗干净并擦干。在清洁方法中，将酒精喷在绝缘体上，然后用干布擦拭。

If the insulator burns during inspection, replace it if it breaks. You need to clean the insulator and oil on the insulator and wipe it dry. In the cleaning method, spray alcohol on the insulator and then wipe it with a dry cloth.

以上是油烟净化器按照规范进行清洗工作的步骤，以上清洗方法都比较仔细，在操作过程中要注意不要损坏某些部件。配件的拆卸也要按照一定的规范进行。关注我们http://www.jnqsg.com了解更多事项！

The above steps are the steps for cleaning the lampblack purifier according to the specifications. The above cleaning methods are very careful. Pay attention not to damage some parts during the operation. The accessories shall also be disassembled according to certain specifications. Follow us http://www.jnqsg.com Learn more!