专注通风管道加工·排烟罩

风管加工：为避免油烟、气体等的物质被排放到室外去，一般的状况下都会设备通风管道的，但因为通风管道大多是一些薄壁、大起伏的产品，在出产和运用进程中经常呈现翘曲变形的问题，关于通风管道会翘曲变形的原因，您知道吗？下面由济南通风管道加工厂家济南成路广通风小编带大家一起来了解一下。

Air duct processing: In order to prevent substances such as oil fumes and gases from being discharged outdoors, ventilation ducts are usually installed. However, because ventilation ducts are mostly thin-walled and large undulating products, they often exhibit warping and deformation problems during production and use. Do you know the reasons for the warping and deformation of ventilation ducts? Below, let Jinan Chenglu Guangtongfeng, a ventilation duct processing manufacturer in Jinan, take you to learn more.

镁水泥在天然养护条件下其体积是一个连续胀大进程，其线胀大率为0.1~0.2%，体积胀大率约为

Magnesium cement undergoes a continuous expansion process in volume under natural curing conditions, with a linear expansion rate of 0.1~0.2% and a volume expansion rate of approximately

菱镁矿在服烧进程中不可避免地发生部分过烧，使一部分MgO呈死烧状况，过烧的MgO水化进程很慢，当已构成强度的水泥石中的MgO再遇水进行水化时，生成Mg(OH)2，体积胀大

During the sintering process of magnesite, partial overburning is inevitable, resulting in a dead burning state of some MgO. The hydration process of overburned MgO is very slow. When MgO in the cement stone that has already formed strength is hydrated with water, it generates Mg (OH) 2, causing volume expansion

轻烧氧化镁中游离CaO水化时体积胀大90%，而卤片中存在着SO42-，当Ca(OH)2转化成石膏时，固体体积将增加2倍以上，导致制品变形，这也是束缚轻烧氧化镁中游离CaO含量、卤片中SO42-含量的原因

During the hydration of free CaO in lightly burned magnesium oxide, the volume expands by 90%, while there is SO42- present in the brine sheet. When Ca (OH) 2 is converted into gypsum, the solid volume will increase by more than twice, causing deformation of the product. This is also the reason why the free CaO content in lightly burned magnesium oxide and the SO42- content in the brine sheet are constrained

MgO-Mg-C12-H2O体系水化进程是一个激烈的放热反响进程，而出产的管道体积又大，若环境温度较高，则反响升温进程，板材本体温度过高，反响不充沛，构成较大的结晶应力和热胀大应力，使制品体积胀大。

The hydration process of MgO-Mg-C12-H2O system is an intense exothermic reaction process, and the volume of the produced pipeline is large. If the ambient temperature is high, it will reflect the heating process. If the temperature of the board body is too high, the response is not sufficient, forming a large crystallization stress and thermal expansion stress, causing the volume of the product to expand.

风管加工设备安排在修建物内时，应考虑修建物楼板、梁的承载才干，需求时应采纳相应办法。关于洁净体系的风管制造应有洁净封闭仓库贮存制品或半制品。

When arranging the air duct processing equipment inside the building, the load-bearing capacity of the building's floor slabs and beams should be considered, and corresponding methods should be adopted when needed. The manufacturing of air ducts for clean systems should have clean enclosed warehouses for storing products or semi-finished products.

风管加工场所应预留现场资料、制品以及半制品的运送通道，风管加工场所的挑选不得阻挠消防通道。大样图、体系图经审查契合要求，并进行了技能及交底。

The air duct processing site should reserve transportation channels for on-site data, products, and semi-finished products, and the selection of air duct processing sites should not obstruct fire exits. The detailed drawings and system diagrams have been reviewed and found to meet the requirements, and skills and disclosures have been made.

风管加作业业地址应有安放施工机具和资料堆积场所，设备和电源应有牢靠的防护设备。作业场所路途应疏通。需求有能满意消防要求的各种器械及设备。

There should be a place for construction equipment and data storage in the air duct and operation site, and the equipment and power supply should have reliable protective equipment. The route to the workplace should be cleared. We need various instruments and equipment that can meet the fire protection requirements.

风管预制应有独立的作业场所，场所应平坦、清洗，加工途径应找平。双面铝箔绝热板风管等其他复合资料风管的场所应单调，应有满意的制品堆积场所。

The prefabrication of air ducts should have an independent workplace, which should be flat and clean, and the processing path should be leveled. The location of double-sided aluminum foil insulation board air ducts and other composite material air ducts should be monotonous, and there should be a satisfactory place for product stacking.

感谢您的阅读，此文的文章来源：山东通风管道加工更多的内容和问题请点击：http://www.jnqsg.com 我们会继续努力的为您提供服务，感谢您的支持！

Thank you for reading. The source of this article is Shandong Ventilation Pipeline Processing. For more information and questions, please click: http://www.jnqsg.com We will continue to work hard to provide you with services. Thank you for your support!

上一篇：纤维织物通风风管的施工方式
下一篇：白铁风管加工质量要注意哪些？