通风管道大家应该都非常熟悉，我们平时在地下车库，在办公楼，在学校都会看见它，通风管道是通风与空调系统的神经元件，大部分由风管加工设备制成，但由于很多原因风管加工设备会导致山东通风管道加工时出现很多问题，比如以下问题。
We should be very familiar with the ventilation duct. We usually see it in the underground garage, office building and school. The ventilation duct is the nerve element of the ventilation and air conditioning system, and most of it is made of the air duct processing equipment. However, due to many reasons, the air duct processing equipment will cause many problems in the processing of the ventilation duct, such as the following problems.
一，禁止风管翘角和弯头，当板被布置和布置时，空气导管成对平行，并且相对的板在长度和宽度上不相等。步骤：打开下料时，应接好板材的边角，检查每张板材的长度、宽度和对角线，使其误差在允许范围内;下料后，与风管相对的两块板材应重叠，以检查尺寸精度。
1、 When the boards are arranged and arranged, the air ducts are parallel in pairs, and the length and width of the opposite boards are not equal. Steps: when opening the blanking, the edges and corners of the plate should be connected, and the length, width and diagonal of each plate should be checked to make the error within the allowable range; After blanking, the two plates opposite to the air duct should be overlapped to check the dimensional accuracy.
表示两对矩形风道是三维的，两个端面不平行；折叠角度不直；对角线不平等；咬的不严格。这种情况往往会造成风管连接受力不均匀，安装后风管不均匀，法兰垫片松动，系统漏气，造成空调负荷损失，延长使用寿命。
It means that two pairs of rectangular air ducts are three-dimensional and the two end faces are not parallel; The folding angle is not straight; Diagonal inequality; The bite is not strict. This kind of situation often leads to uneven force of air duct connection, uneven air duct after installation, loose flange gasket, air leakage of the system, resulting in air conditioning load loss and prolonging service life.
二，处理数据不符合标准，数据不合格，每一步制造风管的要求不严格。
2、 The processing data is not up to standard, the data is not up to standard, and the requirements for each step of air duct manufacturing are not strict.
在使用济南通风管道加工设备制造风管之前，需要对出厂合格证、数据质量确认等表面厚度等数据进行反思。以确保数据可用。板外不平整，厚度不均匀，有明显的压痕、裂纹、砂眼、疤痕、锈蚀等环境;风道三维下沉，前端向外突出，变形明显。影响运行中风管泄漏，空调负荷增加，影响风的寿命和性能。
Before using Jinan ventilation duct processing equipment to manufacture air duct, it is necessary to reflect on the surface thickness data such as factory certificate and data quality confirmation. To ensure that the data is available. There are obvious indentation, crack, sand hole, scar, corrosion and other environment; The air duct sinks in three dimensions, the front end protrudes outwards, and the deformation is obvious. The air duct leakage will affect the operation, the air conditioning load will increase, and the service life and performance of the air conditioner will be affected.
上一篇：通风管道施工中安装吊架有哪些规定？
下一篇：通风管道变形原因分析
