空气是非常重要的在人们的生活中,缺少空气不能活的人会感到窒息,空气中的氧气也对人类生活的基本元素,所以保持室内通风,以满足对氧气的需求,这也是一个通风管道加工影响人们的生活,但在处理的过程中涉及的质量是什么?下面
山东通风管道加工小编就来介绍一下吧。
Air is very important in people's life. People who can't live without air will feel suffocated. The oxygen in the air is also the basic element of human life. Therefore, keep indoor ventilation to meet the demand for oxygen. This is also a ventilation pipe processing that affects people's life, But what is the quality involved in the processing? Let's introduce the processing of Shandong ventilation pipe.
通风管道是通风空调系统的重要组成部分。但由于种种原因，可能导致管道加工设备从加工到通风管道出现问题。
Ventilation duct is an important part of ventilation and air conditioning system. However, due to various reasons, problems may occur in the pipeline processing equipment from processing to ventilation pipeline.
1. 加工材料不符合标准
1. Processing materials do not meet the standards
(1)性能:板材表面不平整，厚度不均匀，有明显的压痕、裂纹、砂、锈等情况;通风管道平面下沉，侧面向外突出，变形明显。
(1) Performance: the surface of the plate is not smooth, the thickness is not uniform, there are obvious indentation, crack, sand, rust and other situations; the plane of the ventilation pipe sinks, the side is protruding outwards, and the deformation is obvious.
(2)影响:运行时通风管道漏水，空调负荷增加，同时风的寿命和性能也受到影响。
(2) Impact: when running, the air duct leaks water, the air conditioning load increases, and the life and performance of the air are also affected.
(3)原因:材质不合格，不能满足通风管道的生产需要。
(3) Reason: the material is not qualified, which can not meet the production needs of the ventilation pipe.
(4)措施:使用通风管道处理设备前，做好通风管道的检查，检查材料出厂合格证、材料质量合格证、外观厚度等，确保材料的可用性。
(4) Measures: before using the ventilation pipe processing equipment, do a good job in the inspection of the ventilation pipe, check the material factory certificate, material quality certificate, appearance thickness, etc., to ensure the availability of materials.
通风管道加工
Ventilation pipe processing
2. 通风管道的弯曲角度和弯头角度是不允许的
2. Bending angle and elbow angle of ventilation pipe are not allowed
(1)性能:矩形通风管道两个相对平面，两端不平行;折叠角度不直;对角线不相等;宽松的咬人。
(1) Performance: two relative planes of rectangular ventilation pipe, two ends are not parallel; the folding angle is not straight; the diagonal is not equal; loose biting.
(2)影响:会使通风管道连接力不均匀，安装后通风管道不直，法兰垫片不紧，漏风系统，空调负荷损失，并缩短使用寿命。
(2) Impact: it will make the connection force of the ventilation pipe uneven, the ventilation pipe is not straight after installation, the flange gasket is not tight, the air leakage system, the air conditioning load loss, and shorten the service life.
(3)原因:板材落料放样不准确;两个通风管道平行，相对板材的长度和宽度不相等。
(3) Cause: the blanking and setting out of the plate are not accurate; the two ventilation pipes are parallel, and the length and width relative to the plate are not equal.
(4)措施:落料时，板材应严格角度、每块板材的长度、宽度及对角线检查，使其偏差控制在允许范围内;板材落料时，通风管道两侧相对的两块板材应重合，以检查尺寸的准确性。
(4) Measures: during blanking, the angle, length, width and diagonal of each plate shall be strictly checked to make the deviation within the allowable range; during blanking, the two plates on both sides of the ventilation pipe shall be overlapped to check the accuracy of the size.
以上是山东通风管道加工小编对通风管道的加工过程中会涉及到的一些质量介绍，希望以上内容对您有所帮助，如果您需要安装通风管道，欢迎您随时与我们联系。
The above are some quality introductions that will be involved in the processing process of the ventilation pipe of Shandong ventilation pipe processing small series. I hope the above content will help you. If you need to install the ventilation pipe, you are welcome to contact us at any time.
上一篇：为什么要对排烟管道包装?
下一篇：饭店厨房排烟罩安装标准
