山东通风管道加工安装应具备的条件:
The requirements for processing and installation of ventilation pipes in Shandong Province are as follows:
(1)济南通风管道的处理条件
(1) Treatment conditions of Jinan ventilation pipeline
1. 一般排风机系统和空调系统的安装应在建筑物围护结构已建好、障碍物已、地面无杂物的情况下进行。
1. The general exhaust fan system and air conditioning system shall be installed when the building envelope has been built, the obstacles have been removed and the ground is free of sundries.
2. 空气净化系统的安装，应在建筑物内部构件安装、墙壁已抹灰、室内无灰尘或防尘措施的地面上进行。
2. The installation of air purification system shall be carried out on the ground where the internal components of the building are installed, the walls are plastered, and there is no dust or dust-proof measures in the room.
3、一般除尘系统风道安装应在车间内进行，安装好工艺设备后或设备底座已确定，设备接头、罩体位置已确定。
3. Generally, the air duct of dust removal system shall be installed in the workshop. After the process equipment is installed or the equipment base has been determined, and the position of equipment joint and cover body has been determined.
4. 现场检查预留孔的位置和尺寸是否符合图纸要求。每一面都比实际截面大100毫米。
4. Check whether the position and size of the reserved holes meet the requirements of the drawings on site. Each side is 100 mm larger than the actual section.
5、作业现场应具备相应的辅助设施，如梯子、货架、防护、消防器材、施工人员的技术、质量、等。
5. The operation site shall be equipped with corresponding auxiliary facilities, such as ladders, shelves, safety protection, fire fighting equipment, technology, quality and safety of construction personnel, etc.
(2)济南通风管道加工材料要求
(2) Jinan ventilation pipe processing material requirements
通风管
Vent pipe
1. 各类板材、管材必须有质量证明文件(包括出厂证明、质量证书、检测报告)和产品清单。
1. All kinds of plates and pipes must have quality certificates (including factory certificates, quality certificates, test reports) and product lists.
2. 成品风道内不得有变形、变形、开裂、孔洞、法兰脱落、开焊、缺铆接、缺螺栓孔等缺陷。
2. There shall be no deformation, deformation, crack, hole, flange falling off, open welding, lack of riveting, lack of bolt hole and other defects in the finished air duct.
3、阀体内安装消声器、罩体、风口等部件应检查调节装置是否灵活，漆膜、漆膜是否损坏。
3. If the muffler, cover, air vent and other parts are installed in the valve body, check whether the regulating device is flexible and whether the paint film and paint film are damaged.
4. 安装材料:螺栓、螺母、垫圈、垫片、密封条、自攻螺钉、拉拔铆钉、焊条、各种帆布、无纺布、射钉、膨胀螺栓等，应符合产品质量要求。
4. Installation materials: bolts, nuts, washers, gaskets, sealing strips, self tapping screws, pull rivets, welding rods, various canvas, non-woven fabrics, shooting nails, expansion bolts, etc., which shall meet the product quality requirements.
(3)济南通风管道加工施工设备
(3) Jinan ventilation pipe processing and construction equipment
手锤、电锤、手摇钻、手锯、电动双刃剪、砂轮锯、角磨机、台钻、电焊工具、扳手、螺丝刀、手剪、链条、高凳、大绳、尖锐冲头、钉枪、毛刷等。
Hammers, electric hammers, hand drills, hand saws, electric double-edged shears, wheel saws, angle grinders, bench drills, welding tools, wrenches, screwdrivers, hand shears, chains, high stools, large ropes, sharp punches, nail guns, brushes, etc.
以上是
山东通风管道加工公司为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：http://www.jnqsg.com
The above is the relevant content introduced by Shandong ventilation pipe processing company. For more information, please visit the website: http://www.jnqsg.com
上一篇：排烟罩的工作原理是什么大家知道吗?
下一篇：为什么要对排烟管道包装?
