专注通风管道加工·排烟罩

　　Ji'nan smoke hood in place, you should check the water level and elevation of all support, see the degree of support of the bracket, the wind pipe in place, you can choose direct and sling two ways

　　对风管断面较小,又方位较低的可选用人工就位办法,只需搭设简易脚手架即可.当风管断面较大且管段较长时,可选用滑轮、倒链、大绳等办法吊装.

　　If the section of the air duct is smaller and the azimuth is lower, the manual placing method can be adopted, and only a simple scaffold can be built. When the section of the wind pipe is larger and the pipe section is longer, the pulley, the chain and the big rope can be used for lifting

　　1、风管安置要求，利用专用东西，以确保缺口形成和胆管形成的角度来看，玻璃纤维复合板管开槽。槽应匀称刷脚刷胶水，以确保槽和关闭槽管联合精密，粘结牢固，玻璃纤维，不袒露。

　　1, the wind pipe placement requirements, the use of special things to ensure that the formation of the gap and bile duct formation point of view, glass fiber composite plate tube slotted. Groove should be symmetrical, brush feet, brush glue, to ensure that groove and groove groove joint precision, bonding firm, glass fiber is not exposed.

　　2、表玻璃纤维复合板玻璃棉板管保温层，因此必要的风墙，可以大概可靠的屏蔽纤维的外外貌层，由于管道墙漆氛围层流与管直接打仗，以是油漆对人体无害。

　　Table 2, glass fiber composite plate glass wool board pipe insulation layer, so the wall outer surface layer can probably reliable shielding fiber, due to pipe wall paint and atmosphere laminar tube directly to war, is harmless to the human body paint.

　　3、玻璃纤维复合板风管加固选择涉及到多变量的边长管道静压风管，布风管钢筋的凹槽钢以外的简化表3.6.10的两种规格，易于利用的槽盒规格。大截面管道可以依赖调解钢筋间距和支持点，以满意风管的加固要求。

　　3, glass fiber composite board wind pipe reinforcement selection involves variable side length pipe, static pressure air duct, high quality cloth duct, reinforced steel channel outside the concave simplified table 3.6.10 two specifications, easy to use groove box specifications. Large section pipes can depend on the spacing and support points of the reinforcement to satisfy the reinforcement requirements of the air duct.

　　4、外貌掩护层的玻璃纤维布管应限定杂身分的玻璃泥土法拉硅技能的根本构成部门，以确保玻璃纤维布的强度和韧性。

　　4, the appearance of the cover layer of glass fiber cloth pipe should be limited to miscellaneous elements of glass, clay, Fala, silicon skills, the basic composition of the Department to ensure the strength and toughness of glass fiber cloth.

　　5、管道端口，具有滋阴，阳榫管应平展，以防备破坏的舌头和嘴，缺口粘结剂粘附必须连结干燥，固化后使管道粘结牢固的粘接部门，连结一个稳固的状态。一个地方来存储玻璃纤维复合板管应该有防雨水和风力的步伐。

　　5, the end of the pipeline, with the function of nourishing yin and Yang, tenon tube should be flat, to prevent the destruction of the tongue and mouth gap binder adhesion must be linked to dry, after curing the adhesive bonding Department pipeline firm, a link to a solid state. A place to store fiberglass composite panels should have the pace of rain, water and wind.

　　本文由济南排烟罩友情奉献.更多有关的知识请点击:http://www.jnqsg.com/我们将用的技术.真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　In this paper, by the Ji'nan hood friendship devotion. More related knowledge: Please click http://www.jnqsg.com/ we will use the most advanced technology. The most sincere attitude, to provide you with the most comprehensive service. More related knowledge and we will continue to offer. Please look forward to.

上一篇：内外同心弧型弯管的错位连接形式
下一篇：通风比局部通风的作用范围大